A simple control law for reducing the effective characteristic acceleration of a solar sail

The direction and magnitude of a solar sail acceleration are strongly related. For this reason, once the characteristic acceleration has been fixed, it is not possible to modulate the acceleration in a particular direction. In this work, a semi-analytical switching control law is derived, enabling a solar sail to emulate a smaller effective characteristic acceleration (without changes in geometry or optical properties); by periodically changing the pitch (cone) angle of the sail, in average over time, the acceleration produced by the sail matches exactly (in both direction and magnitude) that of a “smaller” sail. The range in which this is possible is determined, and the limitations on this range due to the size difference is computed. The method is validated on optimal Earth-Mars trajectories.     

利用视加速度补偿和推力逐级释放的垂直着陆制导方法

针对运载火箭子级垂直返回着陆段的制导问题，本文在应用凸优化的滚动时域在线规划基础上研究了制导鲁棒性的改善策略。为应对着陆后期控制能力不足的情况，在滚动规划过程中引入了推力上界逐级释放的策略。同时，考虑缓解干扰和误差累积的影响，在制导周期内引入视加速度信息对在线规划的推力指令进行补偿，以进一步改善滚动规划的递归可行性。最后，通过数值算例仿真及对比分析验证所提出的补偿策略的有效性。     

Hexapod多自由度微激励系统的振动时域波形控制

摘要： Hexapod多自由度微激励系统常用于航天器有效载荷在轨微振动环境的模拟，但采用现有控制方法无法精确稳定跟踪低频正弦加速度，这是由于系统耦合度高、非线性在低频段较强，被控对象相位滞后过大造成的.针对此问题，基于传统离线迭代控制方法，提出一种复合超前校正、多倍频陷波滤波器的改进离线迭代控制方法.其中，离线迭代进行补偿控制，超前校正进一步补偿系统相位，多倍频陷波滤波器去除非线性干扰.跟踪低频定频正弦加速度的实验结果表明，对比传统离线迭代控制方法，改进方法收敛快、控制精度高；对比现有自适应正弦振动控制方法，改进方法将符合精度要求的加速度控制频带下限由14.5 Hz扩宽至8 Hz.实验结果验证了所提方法的有效性.     

Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

An empirical solar radiation pressure model for satellites moving in the orbit-normal mode

We present a family of empirical solar radiation pressure (SRP) models suited for satellites orbiting the Earth in the orbit normal (ON) mode. The proposed ECOM-TB model describes the SRP accelerations in the so-called terminator coordinate system. The choice of the coordinate system and the SRP parametrization is based on theoretical assumptions and on simulation results with a QZS-1-like box-wing model, where the SRP accelerations acting on the solar panels and on the box are assessed separately. The new SRP model takes into account that in ON-mode the incident angle of the solar radiation on the solar panels is not constant like in the yaw-steering (YS) attitude mode. It depends on the elevation angle of the Sun above the satellite’s orbital plane. The resulting SRP vector acts, therefore, not only in the Sun-satellite direction, but has also a component normal to it. Both components are changing as a function of the incident angle. ECOM-TB has been used for precise orbit determination (POD) for QZS-1 and BeiDou2 (BDS2) satellites in medium (MEO) and inclined geosynchronous Earth orbits (IGSO) based on IGS MGEX data from 2014 and 2015. The resulting orbits have been validated with SLR, long-arc orbit fits, orbit misclosures, and by the satellite clock corrections based on the orbits. The validation results confirm that—compared to ECOM2—ECOM-TB significantly (factor 3–4) improves the POD of QZS-1 in ON-mode for orbits with different arc lengths (one, three, and five days). Moderate orbit improvements are achieved for BDS2 MEO satellites—especially if ECOM-TB is supported by pseudo-stochastic pulses (the model is then called ECOM-TBP). For BDS2 IGSOs, ECOM-TB with its 9 SRP parameters appears to be over-parameterized. For use with BDS2 IGSO spacecraft we therefore developed a minimized model version called ECOM-TBMP, which is based on the same axis decomposition as ECOM-TB, but has only 2 SRP parameters and is supported by pseudo-stochastic parameters, as well. This model shows a similar performance as ECOM-TB with short arcs, but an improved performance with (3-day) long-arcs. The new SRP models have been activated in CODE’s IGS MGEX solution in Summer 2018. Like the other ECOM models the ECOM-TB derivatives might be used together with an a priori model.     

火星大气进入段抗饱和固定时间阻力加速度跟踪制导律设计

研究了具有固定时间收敛特性的火星探测器大气进入段的标称轨迹跟踪制导问题。首先，针对横向运动，给出与速度成线性关系的航向误差漏斗走廊形式，完成了倾侧角的反号逻辑设计。与横程漏斗走廊反号逻辑相比，该逻辑计算量小，更适用于宇航计算机。与航向误差宽度走廊反号逻辑相比，该逻辑在高速状态下能够避免倾侧角的频繁切换，可提高任务成功的概率。其次，针对纵向运动，通过RBF神经网络补偿了倾侧角饱和问题，利用积分滑模设计了阻力加速度固定时间饱和跟踪制导律，其不仅可有效消除滑模控制的抖振问题，且将跟踪误差以两种不同形式引入制导律，能够加速收敛，能够保证跟踪误差在固定时间内快速收敛至0。最后，通过数值仿真验证了所设计的横向倾侧角切换逻辑和纵向制导律对标称轨迹的快速、精确跟踪能力。     

退化发动机加速性能恢复控制方法

针对退化发动机加速性能下降的现象,提出一种变喘振裕度约束的模型预测控制方法。通过分析退化发动机在加速过程中的工作特点,将加速过程分为三个阶段,在不同阶段采取不同的喘振裕度约束。鉴于模型预测控制能够显式处理约束、采用在线滚动优化来获取最优控制输入,采取模型预测控制方法,并采用具有较高实时性的交替方向乘子法求解优化问题,实现了退化发动机加速性能的恢复。数字仿真结果表明,采用本文所提出的加速性能恢复控制方法后,相比退化发动机,加速过程中所耗费的时间缩短了35%以上。     

小样本条件下多应力加速寿命试验预测方法

鉴于导弹中的电子设备价格昂贵、可用于试验的样本量少,在开展加速试验以及寿命预测的实际工作中通常为小样本的背景。文章研究探索小样本条件下多应力加速试验寿命预测方法,分别建立通用对数线性模型、 BAS-BP神经网络模型、灰色–支持向量回归模型,结合多应力加速试验数据在各应力条件下的样本容量分别为 56组、20组、10组、5组的情况下,比较 3种模型的预测效果,分析各模型的适用场合和时机,探索小样本条件下模型的选优问题,为小样本条件下多应力加速试验寿命预测提供有益的借鉴。     

某型民用飞机电源系统负加速度试飞研究

首先对民用飞机电源系统负加速度试飞进行简要说明,提出民用飞机电源系统负加速度试飞的原因和目的。其次对电源系统负加速度试飞条件、试飞方法和试飞程序进行说明。对电源系统负加速试飞结果进行分析评估,表明电源系统设计是满足设计要求和民用航空标准要求的。最后对负加速度试飞中注意事项进行了详细说明,为其它机型飞机进行负加速度试飞提供借鉴。     

基于退化模型的失效机理一致性检验方法

有效的加速试验必须保证产品的失效机理不变。针对加速退化试验(ADT)可靠性建模的特点,提出了一种基于退化模型的失效机理一致性检验方法。以基于随机过程和基于退化轨迹拟合的退化模型为例,通过加速系数的2种等效定义分别建立了模型参数与失效机理不变的内在联系,进一步推导出其参数在不同应力下须满足的关系。在合理假定检验样本服从正态分布的基础上,利用t统计量对样本的一致性进行检验。通过2个ADT实例验证了所提检验方法的合理性与可行性。